Thermo Scientific 42iQD Скачать руководство пользователя страница 120

Страница: 120 / 286

Operation

Settings

3-96

42iQD Instruction Manual

Thermo Scientific

The Alarm Setpoints screen allows the user to view and set all settable

alarm minimum and maximum values. Alarm setpoints can also be set in

Settings>Health Check>Status and Alarms screens.
Use the



and



buttons to move up and down and the



and



buttons to move left and right.

Note

User cannot set alarm limits outside of the acceptable range. The

minimum and maximum alarm limit can also be set by pressing on the

corresponding buttons located in the Settings>Health Check>Status and

Alarms screen. See “

Status and Alarms

” on page

3-37

▲

Home Screen>Settings>Instrument Settings>Alarm Setpoints

The Alarm Setpoints screen contains the following information:

●

Across:

●

Variable:

Lists the items that have settable alarm limits.

●

Low Alarm:

User sets low alarm for item.

●

High Alarm:

User sets high alarm for item.

●

Units:

Units for each item (not settable).

●

Down:

●

Concentration

concentration alarm.

●

Bkg Check Offset:

User can set the maximum allowable

background reading offset for calibration and calibration checks.

This is set with the high alarm only.

Alarm Setpoints

Содержание 42iQD































































































































































































































































































Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQD, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды