Thermo Scientific 42iQD Скачать руководство пользователя страница 179

Страница: 179 / 286

Maintenance

Pump Rebuilding

Thermo Scientific

42iQD Instruction Manual

5-5

Use the following procedure to rebuild the pump.
Equipment required:

Pump rebuild kit
Phillips screwdriver, #1
Marking pencil or marker
Allen wrench, 2.5 mm

Figure 5–2.

Pump

Disassembly:

Note

Parts removed must be replaced exactly as found. If repairing

multiple pumps, take care not to mix parts.

▲

Turn instrument OFF, unplug the power cord, and remove the cover.

Make a sketch of the position of any tubes and fittings for ease of re-

assembly later.

Mark the position of the pump headplate, intermediate plate and

compressor housing relative to each other by drawing a line on the

edges with a pencil or marker to insure proper re-assembly.

One of the aluminum compressor housing covers must be removed to

gain access to the inside of the compressor housing. Remove the four

Pump Rebuilding

Содержание 42iQD































































































































































































































































































Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQD, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды