manualshive.com logo in svg

Thermo Scientific 117080-00, Инструкция по эксплуатации


Поделиться
Скачать
background image

Maintenance 

Cleaning the Optics 

5-6

     48iQ Instruction Manual 

Thermo Scientific 

 

Best results are obtained when the optics are cleaned prior to calibration. 
The cleanliness of the mirrors should be checked any time the intensity is 
below 200,000 Hz, since one cause of low output is light attenuation due 
to dirt on the mirrors. 

 

Equipment Damage  

Some internal components can be damaged by small 

amounts of static electricity. A properly grounded antistatic wrist strap 
must be worn while handling any internal component. For more 
information about appropriate safety precautions, see the “

Servicing

” 

chapter. 

▲

  

Use the following procedure to clean the mirrors. 

Equipment Required: 

Hex drive, 9/64 

1.

 

Turn off power and disconnect power line. 

2.

 

Using 9/64 hex drive, remove the field mirror by removing the four #8-
32 socket cap head screws holding it to the main bench. 

 

Figure 5–3.

 Removing the Field Mirror 

Cleaning the

Optics

Содержание 117080-00





































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 117080-00

JGR RL1 Manual preview
RL1
Бренд: JGR Страницы: 12
MadMan EMS-3 Operating Manual preview
EMS-3
Бренд: MadMan Страницы: 37
MADDALENA microCLIMA U Installation And Operating Instructions preview
microCLIMA U
Бренд: MADDALENA Страницы: 5
Sanmenxia ZX400 Operation Manual preview
ZX400
Бренд: Sanmenxia Страницы: 17
SANKO SM-1100 Instruction Manual preview
SM-1100
Бренд: SANKO Страницы: 25
Samson 2162 Parts And Technical Service Manual preview
2162
Бренд: Samson Страницы: 2
Task Force Tips BLITZFIRE Series Instruction For Operation And Maintenance preview
BLITZFIRE Series
Бренд: Task Force Tips Страницы: 20
Facom DX.V12A Instruction Manual preview
DX.V12A
Бренд: Facom Страницы: 48
Didactum Monitoring System 500 II DC Quick Start Manual preview
Monitoring System 500 II DC
Бренд: Didactum Страницы: 2
M-Sure MS-535 Series Quick Start Manual preview
MS-535 Series
Бренд: M-Sure Страницы: 2
Lennox Smart Air Quality Monitor Installation And Setup Manual preview
Smart Air Quality Monitor
Бренд: Lennox Страницы: 28
Roland KR-1070 Owner'S Manual preview
KR-1070
Бренд: Roland Страницы: 96
Sensitech FreezeAlert Instructions For Use preview
FreezeAlert
Бренд: Sensitech Страницы: 2
Tektronix MTX100B Technical Reference preview
MTX100B
Бренд: Tektronix Страницы: 116
Deprag 385484 A Operating Instruction Booklet preview
385484 A
Бренд: Deprag Страницы: 28
Ocean Reef GSM Mercury Owner'S Manual & Installation Manual preview
GSM Mercury
Бренд: Ocean Reef Страницы: 24
Hanna Instruments HI6421P Quick Reference Manual preview
HI6421P
Бренд: Hanna Instruments Страницы: 2
Cressi NEPTO Instruction Manual preview
NEPTO
Бренд: Cressi Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды