Texas Instruments TMS320VC5509 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 285

Texas Instruments TMS320VC5509 Скачать руководство пользователя страница 129

Setting the Receive Frame-Sync Mode

Receiver Configuration

7-24

SPRU592E

Table 7

−

19. Register Bits Used to Set the Receive Frame Sync Mode (Continued)

Register

Function

Name

Bit

SRGR2

15

GSYNC

†

Sample Rate Generator Clock Synchronization Mode
If the sample rate generator creates a frame-sync signal (FSG) that is derived
from an external input clock on the CLKS or CLKR pin, the GSYNC bit
determines whether FSG is kept synchronized with pulses on the FSR pin.

GSYNC = 0

No clock synchronization is used: CLKG oscillates without
adjustment, and FSG pulses every (FPER + 1) CLKG
cycles.

GSYNC = 1

Clock synchronization is used. When a pulse is detected
on the FSR pin:

-

CLKG is adjusted as necessary so that it is
synchronized with the input clock on the CLKS or
CLKR pin.

-

FSG pulses.
FSG

only

pulses in response to a pulse on the FSR

pin. The frame-sync period defined in FPER is
ignored.

SPCR1

15

DLB

Digital Loopback Mode

DLB = 0

Digital loopback mode is disabled.

DLB = 1

Digital loopback mode is enabled. The receive signals,
including the receive frame-sync signal, are connected
internally through multiplexers to the corresponding
transmit signals.

SPCR1

12-11 CLKSTP

Clock Stop Mode

CLKSTP = 0Xb

Clock stop mode disabled; normal clocking for non-SPI
mode.

CLKSTP = 10b

Clock stop mode enabled, without clock delay. The
internal receive clock signal (CLKR) and the internal
receive frame-synchronization signal (FSR) are internally
connected to their transmit counterparts, CLKX and FSX.

CLKSTP = 11b

Clock stop mode enabled, with clock delay. The internal
receive clock signal (CLKR) and the internal receive
frame-synchronization signal (FSR) are internally
connected to their transmit counterparts, CLKX and FSX.

†

The clock synchronization provided through the GSYNC bit is not supported on TMS320VC5501 and TMS320VC5502
devices.

«
...
127
128
129
130
131
...
»

Содержание TMS320VC5509






























































































































































































































































































Отзывы:

Нет отзывов