Tennant 92 GR Скачать руководство пользователя страница 5

Страница: 5 / 79

92GR MM188 (10---87)

WARNING: Always engage the hopper

support bar before working under a raised

hopper. Do not rely on the machine hydraulic

system to keep the hopper in the “raised”

position. The hydraulic system may leak

internally, allowing the hopper to lower, crushing

anything under it.

WARNING: Avoid moving parts of the

machine. Do not wear loose jackets, shirts,

or sleeves when working on machine because of

the danger of becoming caught in moving parts.

Keep shields and guards in position. Wear

approved eye protection. If adjustments must be

made while the engine is running, use extreme

caution around hot manifolds, moving parts,

belts, etc.

WARNING: Always stop the machine on a

level surface, stop the engine and engage

the parking brake before working on the machine

to keep it from rolling.

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды