Tennant 92 GR Скачать руководство пользователя страница 58

Страница: 58 / 79

3-65559

92GR MM188 (11---87)

BELTS AND CHAINS

ENGINE FAN BELT

To tighten the fan belt, loosen the alternator

adjusting bolts and pull out on the alternator by hand

until the belt is just snug. Do not use a pry bar on the

alternator to tension the fan belt, as damage to the

bearings will result. Then tighten the alternator

adjusting bolts.

Check the fan belt tension after every 50 hours of

operation.

Proper belt deflection is obtained when the belt

deflects 0.5 in (13 mm) from a force of 10 to 12 lb

(4.5 to 5.4 kg) applied at the midpoint of the longest

span.

00577

ENGINE FAN BELT

A. Fan Belt

B. 0.5 in (13 mm)

STATIC DRAG CHAIN

A static drag chain is provided to prevent the buildup

of static electricity in the machine. The chain is

attached to the machine by a rear brush skirt

retaining bolt.

Check the chain for wear. Make sure that it is making

contact with the floor at all times.

01479

STATIC DRAG CHAIN

A. Rear Dust Skirt

B. Static Drag Chain

C. Rear Tire

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды