Tennant 92 GR Скачать руководство пользователя страница 25

Страница: 25 / 79

92GR MM188 (10---87)

2-10

HYDRAULIC PRESSURE GAUGE

The hydraulic pressure gauge registers the hydraulic

pressure in the main brush circuit. Normal down

pressure ranges with the brush up and running are

300 to 500 psi (2070 to 3450 kPa) and from 1800 to

2200 psi (12,410 to 15,170 kPa) with the brush down

and running. It is normal for the gauge needle to

move around. It moves around due to uneven or

high spots in the floor.

Prolonged pressures above 2250 psi (15,510 kPa)

will cause the wire brush to stall and will damage the

brush and hydraulic system.

STABILIZER LEG

The stabilizer leg projects forward to act as an

anti---tipping device when the machine is being high

dumped. Check the stabilizer leg to be sure it is

projecting forward when the machine is being high

dumped and is fully retracted when the hopper is in

the “operating” position.

01440

RETRACTED STABILIZER LEG

A. Machine Frame

B. Stabilizer Leg

FUSES AND CIRCUIT BREAKERS

Fuses are a one---time circuit protection device

designed to stop the flow of current in the event of a

circuit overload. Never substitute higher value fuses

than those specified in this manual.

Circuit breakers are reusable circuit protection

devices designed to stop the flow of current in the

event of a circuit overload. Once tripped, circuit

breakers must cool before they automatically reset.

If the overload which caused the circuit breaker to

trip is still present in the circuit, the circuit breaker

will continue to stop current flow until the overload is

corrected. The chart below shows the various fuses

and circuit breakers, the electrical components they

protect, and their locations in the machine.

PROTECTIVE

CIRCUIT

DEVICE

RATING

PROTECTED

LOCATION

FU--- 1

50 A

Diesel Glow Plug

Diesel Control Unit

CB--- 1

25 A

Dust Shaker Motors

Electric Breaker Box

CB--- 2

15 A

Operating Lamps

Electric Breaker Box

CB--- 3

15 A

Gauges

Electric Breaker Box

CB--- 4

15 A

Actuator

Electric Breaker Box

CB--- 5

15 A

Turn Signal Lamps

Electric Breaker Box

CB--- 6

15 A

Heater, Defroster, Fan

Electric Breaker Box

CB--- 7

15 A

Back--- up Alarm

Electric Breaker Box

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды