Tennant 92 GR Скачать руководство пользователя страница 64

Страница: 64 / 79

3-65565

92GR MM188 (11---87)

01486

MAIN BRUSH IDLER ARM

A. Brush Idler Arm

B. Plastic Screw

C. Arm Retaining Bolt

7. Pull the brush idler arm off the arm hub.

NOTE: If the brush idler arm does not come off

easily, remove the plastic screw located next to the

hole where the brush idler arm retaining bolt was

mounted. Thread the brush idler arm retaining bolt

into the threaded hole the plastic screw came out of.

Tighten the retaining bolt until it forces the brush idler

arm loose. Remove the brush idler arm retaining bolt

and replace it with the plastic screw.

8. Pull the main brush off the brush drive plug and

out of the main brush compartment.

NOTE: If the brush dose not come off easily, remove

the three plastic screws located on the brush drive

arm and thread bolts into the holes to push the brush

off the drive plug.

9. Clean the brush drive and idler plugs. Apply a

coat of grease to them to make brush removal

and installation easier.

10. Place the new or rotated main brush on the

floor next to the access door.

11. Align the main brush drive slots with the drive

keys on the main brush drive plug.

12. Slide the main brush into the brush

compartment and onto the drive plug. Make

sure the drive slots and keys line up.

NOTE: The bottom of the brush arms should be less

than 1 in (25 mm) from the floor. If they are not, turn

the brush height adjustment knob to position the

arms.

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды