Tennant 92 GR Скачать руководство пользователя страница 39

Страница: 39 / 79

92GR MM188 (11---87)

3-65540

LUBRICATION

ENGINE

Check the engine oil level daily. Change the engine

oil and oil filter after every 50 hours of operation.

Change the engine oil more frequently if the

environment is extremely dusty. Use only CD or CE

rated engine oil.

The following SAE oil grades are general

recommendations for engines during the changing

seasonal temperatures.

BELOW 0+F

0+ to 32+F

32+ to 75+F

ABOVE 75+F

(BELOW --- 17+C)

(--- 17+ to 0+C)

(0+ to 24+C)

(ABOVE 24+C)

SAE 5W

SAE 10W

SAE20W

SAE 30

SAE 5W--- 20

SAE 10W--- 30

SAE 5W--- 30

SAE 10W--- 40

Multi---grade oil should cover the single grade

recommendation for the temperatures involved. The

engine oil capacity is 7 qt (6.6 L) with filter.

REAR WHEEL SUPPORT PIVOT

There is a grease fitting which is used to lubricate

the rear wheel support pivot bearing.

Access to the grease fitting is through the center rear

access door. Apply a general purpose, water

resistant, lithium base, moly---disulphide EP grease

after every 200 hours of operation.

01452

REAR WHEEL SUPPORT PIVOT

A. Wheel Support

B. Grease Fitting

C. Fuel Tank

STEERING GEAR

The steering gear has been lubricated at the factory

and should not require any additional lubricant

unless a massive leak occurs.

A square head plug located on the left side of the

steering gearbox is provided to fill the steering gear

with grease if necessary.

The proper lubricant is grade 1 calcium soap base

EP grease.

01457

STEERING GEAR LUBRICATION PLUG

A. Steering Gearbox

B. Fill Plug

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды