Tennant 92 GR Скачать руководство пользователя страница 62

Страница: 62 / 79

3-65563

92GR MM188 (11---87)

TO ADJUST STABILIZER LEG

1. Place the hopper in the “operating” position.

2. Make sure the front bumper is not resting on

the stabilizer leg assembly. If it is, loosen the

leg assembly mounting bolts, slide the

assembly down, and retighten the bolts.

3. Loosen the activating arm pinch bolt.

4. Hold the stabilizer leg in the “fully raised”

position.

01440

STABILIZER LEG

A. Stabilizer Leg

B. Arm

C. Pinch Bolt

D. Bumper

5. Position the arm so it contacts the bottom of

the front bumper and tighten the pinch bolt.

6. Start the engine and raise the hopper. Check to

make sure the leg is in the “lowered” position.

7. Lower the hopper and check to make sure the

leg is fully retracted into the “raised” position.

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды