Tennant 92 GR Скачать руководство пользователя страница 78

Страница: 78 / 79

4-1

92GR MM188 (11---87)

HARDWARE INFORMATION

The following charts state standard plated hardware

tightening ranges for normal assembly applications.

Decrease the specified torque by 20% when using a

thread lubricant. Do not substitute lower grade

hardware for higher grade hardware. If higher grade

hardware than specified is substituted, tighten only

to the specified hardware torque value to avoid

damaging the threads of the part being threaded

into, as when threading into speed nuts or

weldments.

STANDARD BOLT TORQUE CHART

Thread

SAE Grade 5

SAE Grade 8

Siz

Torque ft lb (Nm)

______________________________________________________________

0.25 in

7---10 (9---14)

10---13 (14---18)

0.31 in

15---20 (20---27)

20---26 (27---35)

0.38 in

27---35 (37---47)

36---47 (49---64)

0.44 in

43---56 (58---76)

53---76 (72---103)

0.50 in

65---85 (88---115)

89---116 (121---157)

0.62 in

130---170 (176---231)

117---265 (159---359)

0.75 in

215---280 (291---380)

313---407 (424---552)

1.00 in

500---650 (678---881)

757---984 (1026---1334)

NOTE: Decrease torque by 20% when using a thread

lubricant.

METRIC BOLT TORQUE CHART

Thread

Class 8.8

Class 10.9

Size

Torque ft lb (Nm)

______________________________________________________________

2 (3)

3 (4)

4 (5)

6 (8)

7 (9)

10 (14)

18 (24)

25 (34)

M10

32 (43)

47 (64)

M12

58 (79)

83 (112)

M14

94 (127)

133 (180)

M16

144 (195)

196 (265)

M20

260 (352)

336 (455)

M24

470 (637)

664 (900)

NOTE: Decrease torque by 20% when using a thread

lubricant.

BOLT IDENTIFICATION

Identification

Specification

Grade Marking

and Grade

____________________________________________________

SAE---Grade 5

SAE---Grade 8

ISO---Grade 8.8

ISO---Grade 10.9

01395

THREAD SEALANT AND LOCKING COMPOUNDS

Thread sealants and locking compounds may be

used on this machine. They include the following:

Locktite 515 sealant --- gasket forming material.

TENNANT

Part No. 75567,15 oz (440 ml)

cartridge.

Locktite 242 blue --- medium strength thread

locking compound. TENNANT

Part No.

32676, 0.5 ml tube.

Locktite 271 red --- high strength thread locking

compound. TENNANT

Part No. 19857, 0.5 ml

tube.

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды