Tennant 92 GR Скачать руководство пользователя страница 43

Страница: 43 / 79

92GR MM188 (11---87)

3-65544

SPEED LIMITER

The machine speed limiter limits the maximum

speed the machine can travel when the hopper is

raised. The speed limiter should be adjusted

whenever the pump control linkage is adjusted. The

machine should not travel more than 2 mph (3.2

km/h) with the hopper raised.

The speed limiter is adjusted by tightening or

loosening the speed limiter cable. One threaded end

of the cable is located on the right lift arm. The other

end of the cable, which is also threaded, is located

on a flat sided sheave next to the directional control

pedal. Tighten the cable to reduce the machine

speed when the hopper is raised. Loosen the cable

to increase the machine speed when the hopper is

raised.

01463

SPEED LIMITER CABLE

A. Speed Limiter Cable

B. Flat Sided Sheave

C. Cable Adjusting Nut

D. Directional Pedal

HYDRAULIC FLUID LEAKS

Fluid escaping from a very small hole can be almost

invisible. Use a piece of cardboard or wood, rather

than hands, to search for suspected leaks.

00002

HYDRAULIC PINHOLE LEAK

A. Cardboard

B. Pinhole Leak

C. Magnifying Glass

If injured by escaping fluid, see a doctor at once.

Serious infection or reaction can develop if proper

medical treatment is not administered immediately.

WARNING: Escaping hydraulic fluid under

pressure can have sufficient force to

penetrate the skin, causing serious personal

injury. Before applying pressure to the system, be

sure all connections are tight and that lines,

pipes, and hoses are not damaged.

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды