Tennant 92 GR Скачать руководство пользователя страница 2

Страница: 2 / 79

This manual is furnished with each new TENNANT

Model 92GR. It provides necessary operating and

preventive maintenance instructions. Read this manual completely and understand the machine before

operating or servicing it.

This manual covers all machine variations and standard accessories. The tabbed instruction portion of the

manual consists of the Specification, Operation, Maintenance, and Appendix sections. The tabbed parts section

consists of the Standard Model Parts, Accessories, Hydraulic Components, and Engine Parts sections.

All right side and left side references to the machine are determined by facing the direction of forward travel. All

hardware considered to be of a common nature or locally available has been omitted from the parts sections.

Be aware that this machine may contain metric hardware. Make sure you use equivalent hardware when

replacement becomes necessary.

This machine will provide excellent service. However, the best results will be obtained at minimum costs if:

The machine is operated with reasonable care.

The machine is maintained regularly --- per the maintenance instructions provided.

The machine is maintained with Tennant Company supplied or equivalent parts.

Parts and supplies may be ordered by phone or mail from any Tennant Company parts and service center,

distributor, or from any of the Tennant Company subsidiaries. Before ordering parts or supplies, be sure to have

your machine model number and serial number handy. Fill out the data block below for future reference. The

telephone numbers, telex numbers, mailing addresses, and locations of those outlets are listed in the Customer

Documents section of the manual.

MACHINE DATA

Please fill out at time of installation.

Machine Serial Number ---

Engine Serial Number ---

Sales Representative ---

Date of Installation ---

Manual Number --- MM188

Revision: 02

Published: 11---87

04300

Trademark Registered in:

Austria, Benelux, Denmark, England, France, Germany, Italy, Spain, Switzerland,

United States, Argentina, Australia, Canada, Japan, Mexico, Sweden, by TENNANT COMPANY, Minneapolis,

Minnesota, U.S.A.

Acknowledgments:

Technical information and/or illustrations supplied by Teledyne Continental Motors,

Industrial Products Division: Cessna Fluid Power Division; Eaton Corporation, Hydraulics Division.

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды