Tennant 92 GR Скачать руководство пользователя страница 16

Страница: 16 / 79

2-1

92GR MM188 (10---87)

PREPARATION FOR OPERATION

AFTER UNCRATING AND BEFORE OPERATING THE

MACHINE:

1. Check the machine for shipping damage.

2. Read this manual carefully before operating or

servicing the machine.

WARNING: Do not operate the machine

until you have read and understood the

operating instructions and are properly trained.

Failure to do so could result in severe personal

injury.

3. Check the hydraulic fluid level in the hydraulic

fluid reservoir using the sight gauge provided.

TENNANT

hydraulic fluid is recommended. If

TENNANT

hydraulic fluid is not available,

use only new---approved hydraulic fluid. See

Hydraulics in the Maintenance section.

4. Check the engine oil level.

5. Check the radiator coolant level.

WARNING: If the coolant is hot or if the

engine has been operating, let the engine

cool. Hot coolant could scald or cause severe

burns. If in doubt, let the coolant cool before

releasing pressure in the cooling system.

6. Check the brush adjustment, as described in

Maintenance section.

7. Fill the fuel tank.

Содержание 92 GR
















































































Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды

Tennant 92 GR, Руководство оператора

Результаты поиска

Содержание 92 GR

Отзывы:

Похожие инструкции для 92 GR

Бренды по названию

Популярные бренды