Teltone TSP Edge Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 177

background image

TSP Edge User’s Manual

40-400-00065, Rev. E

27

Note:

If using only one port on a Dual T1/E1 that is configured for External

Clock, port 2 must be used and will derive its clock from the equipment under
test. If using both ports, the device connected to Port 1 must use the same
clocking reference as the device connected to port 2.

Signaling

With

Signaling

, both ends need to match, otherwise synchronization will not be

achieved. CAS is considered a more common format for voice traffic while FAS is
used for data traffic. The CRC-4 option is used for error detection. The Edge does not
report CRC-4 information.

Line Coding

For

Line Coding

,

AMI

suffices if no DDS data exists on any of the E1 channels.

HDB3

is used when DDS data channels are present to compensate for when an all

Zeros state exists (when equipment is off). This can lead to lost of synchronization on
the E1 data stream due to too many successive zeros.

PCM Encoding

For

PCM Encoding

, the choices are mu-law and a-law. For T1, mu-law is the

default. This is the PCM encoding and companding standard used in North America
and Japan. For E1, a-law is the default and is the PCM encoding and companding
standard used in Europe.

Important:

On Dual T1/E1 modules, both channels are configured for the same

clock, signaling, and line coding. Ensure the parameters are consistent with the
configuration of the equipment under test. This information can be found in the
equipment manual or by contacting the vendor.

Unassigned Channels Idle State

The Unassigned Channels Idle State defines the signaling state for E1 channels that
have not been assigned to any control set, and therefore are not associated with any
template. You can select an idle signaling state associated with a particular protocol
or define the actual bit pattern directly.

To change the default idle state for unassigned channels, see “Unassigned Channels
Tab” on page 50. For information about the Channels tab, see “Channels Tab” on
page 29.

«
...
35
36
37
38
39
...
»

Содержание TSP Edge


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSP Edge

Бренд: Lauterbach Страницы: 61

3CR860-95 - OfficeConnect Secure Router

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 26

Бренд: Oracle Страницы: 24

Бренд: Winext Страницы: 37

Бренд: Usr Страницы: 2

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Hollywood DV-Bridge

Бренд: Dazzle Страницы: 63

Бренд: Radicom Страницы: 27

Бренд: Kanguru Страницы: 13

Бренд: Eicon Networks Страницы: 32

Бренд: Juniper Страницы: 7

Бренд: Daedalon Страницы: 6

Бренд: Valcom Страницы: 4

Бренд: Airlink101 Страницы: 46

Бренд: ZALMAN Страницы: 9

Бренд: MSNswitch Страницы: 2

Бренд: iDirect Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды