Teltone TSP Edge Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 177

background image

TSP Edge User’s Manual

40-400-00065, Rev. E

14

The green POWER LED on the front panel will indicate the status of the system. The
LED should be solid green. If the LED fails to light, check your power connections
and verify the switch is in the ON position. If the LED still fails to light, disconnect
power immediately and contact Teltone Technical Support at 425-951-3390.

Important:

Adequate airflow must be maintained in order for the unit to

operate correctly. Do not wrap the unit in blankets, paper or other material that
may impede ventilation.

Installing Edge Software

The Edge configuration software is supplied on a CD-ROM disk and uses the
common Windows setup routine. Ensure you have the latest version by going to the
Teltone website (www.teltone.com) and verifying the version available or call
Teltone technical support.

An autorun facility initiates the installation process automatically when the CD-ROM
is installed into the disk drive. An alternative method is to insert the CD-ROM, then
select START, RUN, BROWSE, then choose your CD-ROM drive, and the file
labeled SETUP.EXE. Follow the on screen instructions.

For information about the current and previous versions of the software, see
“Revision History” on page 119.

PROGRAMMING THE EDGE

The Edge configuration software installed on the PC controls the Edge unit and its
configuration. Multiple projects can be saved and used for different testing
applications and units.

Basics

The Edge configuration software allows a user to define Edge

Project

configurations

in terms of

Units

,

Templates

, and

Control Sets.

A

Unit

defines the configuration of a physical Edge unit, the communications

interface used to control it, the hardware modules installed in it, and configuration
parameters for those hardware modules. Within a unit are:

•

Slots

- the physical card slots where modules are installed

•

Ports

- the individual connectors on the modules

•

Channels

- the individual lines or timeslots on each port. Each channel is

identified throughout the configuration software using a unique ID string,
based upon the channel’s location within a particular unit (see “Channel
Identification” on page 30).

«
...
22
23
24
25
26
...
»

Содержание TSP Edge


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSP Edge

Бренд: GE Страницы: 146

Бренд: Paradox Страницы: 4

Бренд: Salusfin Страницы: 6

Бренд: Netopia Страницы: 38

Бренд: Industrex Страницы: 51

Бренд: Maxim Страницы: 26

Бренд: NetComm Страницы: 3

IAR KickStart Kit TWR-K60N512-IAR

Бренд: IAR SYSTEMS Страницы: 8

Бренд: IBASE Technology Страницы: 71

Бренд: Net to Net Technologies Страницы: 4

Бренд: E-TOP Страницы: 24

Бренд: Intellinet Страницы: 12

Бренд: Ubiquiti Страницы: 20

Fan Tray 8820-S2-900

Бренд: Paradyne Страницы: 6

Бренд: Xmart Страницы: 8

Бренд: C&T Solution Страницы: 129

Converter Board R0E521237CFK00

Бренд: Renesas Страницы: 6

Бренд: Intel Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды