Teltone TSP Edge Скачать руководство пользователя страница 140

Страница: 140 / 177

TSP Edge User’s Manual

40-400-00065, Rev. E

130

Analog Loop Start FXS

Analog Loop Start FXS - Call Terminate

Off-hook by equipment under test.

Delay Before Dialtone

timer starts.

Delay Before Dialtone

timer expires.

Dial Tone Length

timer starts.

Dial tone starts from Edge

Dial Tone Length

timer expires.

Dial tone ends – simulates reception of first dialed digit.

Delay Before Ringback

timer starts.

Delay Before Ringback

timer expires – simulates completion of dialing and

network setup delays.
Ringback start from Edge.

Ringback Length

timer starts.

Ringback Length

timer expires.

Ringback ends – simulating answer.

Call Duration

timer starts.

Delay Before Message

timer starts.

Delay Before Message

timer expires.

Edge starts playing audio message.

Edge detects on-hook from equipment under test.

Far-end Disconnect

timer starts.

Note: If

Call Duration

timer expires before detecting on-hook from

the equipment under test, the Edge will send 850ms COD.

Far-end disconnect

timer expires.

Disconnect to start of new call

timer starts.

Note: If equipment under test goes back off-hook before the

Far-End

Disconnect

timer expires, the Edge goes back to looking for step 6.

Disconnect to start of new call

timer expires.

Edge ready to receive next call.

If Dial Tone is disabled in template, proceed directly to step 2.

If Ringback is disabled in template, proceed directly to step 4.

If no Audio Message is programmed for the channel, proceed directly to step 6.

Disconnect
To Start Of

New Call

Far-End Disconnect

guard time

Call Disconnect

Call Setup

Call Connected

Delay Before

Dial Tone

From TSP

Ringback

From TSP

Delay Before

Message

TSP Plays

Audio

Message

Delay Before

Ringback

Содержание TSP Edge


















































































































































































Результаты поиска

Содержание TSP Edge

Отзывы:

Похожие инструкции для TSP Edge

Бренды по названию

Популярные бренды

Teltone TSP Edge, Руководство пользователя

Результаты поиска

Содержание TSP Edge

Отзывы:

Похожие инструкции для TSP Edge

Бренды по названию

Популярные бренды