Teltone TSP Edge Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 177

background image

TSP Edge User’s Manual

40-400-00065, Rev. E

125

APPENDICES

Call Timings and Process Flowcharts

Call Timings

Timings are used to control the intervals of all the different parts of the call process while the
TSP Edge is originating or terminating calls. The default times should be appropriate for
most testing.

There are three sections on the Timings screen:

Timings in the

Originating Calls

section are used when the Edge is generating calls to

the equipment under test.

Timings in the

Terminating Calls

section are used when the Edge is receiving

incoming calls from the equipment under test.

Timings in the

All Calls

section apply to both incoming and outgoing calls.

Not all timings are used by each protocol or by each call type. The Timings tab on the
Templates screen in the Edge configuration software only displays the timings that are
appropriate to the selected protocol. For details on how the timings are applied, see “Call
Process Flowcharts” on page 128.

The following describes each timing parameter.

Originating Calls

Wait For Seize
Acknowledge

Time Edge waits to receive a seize acknowledge after
sending a seizure.

Wait For Delay Dial Start

Time Edge waits to receive the beginning of a Delay Dial
signal after sending a seizure.

Wait For Wink Start

Time Edge waits to receive the beginning of a Wink signal
after sending a seizure.

Wait For Delay Dial End

Time Edge waits to receive the end of a Delay Dial signal
after receiving the beginning of the Delay Dial signal.

Wait For Wink End

Time Edge waits to receive the end of a Wink signal after
receiving the beginning of the Wink signal.

Delay Before Dial

The delay before the Edge starts transmitting digits for
each call made by the Edge.

Wait for Answer

The time the Edge waits before abandoning a call if there is
no answer.

«
...
133
134
135
136
137
...
»

Содержание TSP Edge


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSP Edge

Бренд: D-Link Страницы: 2

OfficeConnect 1600

Бренд: 3Com Страницы: 8

Бренд: 3Com Страницы: 8

Бренд: Idis Страницы: 123

Бренд: Idis Страницы: 29

Бренд: Idis Страницы: 28

DirectIP DR-1304P

Бренд: Idis Страницы: 82

Бренд: iDirect Страницы: 130

Бренд: QNAP Страницы: 20

Бренд: Konig Страницы: 73

Бренд: Amplifier Tech Страницы: 36

Бренд: H3C Страницы: 26

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

FRDM-STBC-SA9500

Бренд: Freescale Semiconductor Страницы: 2

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

Бренд: IEI Technology Страницы: 86

Lite N42B1P Series

Бренд: Dahua Technology Страницы: 14

Бренд: 3Ware Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды