Teltone TSP Edge Скачать руководство пользователя страница 147

Страница: 147 / 177

TSP Edge User’s Manual

40-400-00065, Rev. E

137

T1/E1 Ground Start FXS - Call Originate

Edge sends ringing to equipment under test

Wait For Answer

timer starts.

Edge detects answer from equipment under test.

Call Duration

timer starts.

Delay Before Message

timer starts

Note: If

Wait for Answer

timer expires before the Edge detects

answer from equipment under test, the Edge will proceed to step 4.

Delay Before Message

timer expires.

Edge starts playing audio message.

Edge detects on-hook from equipment under test.

Far-end Disconnect

timer starts.

Note: If

Call Duration

timer expires before detecting on-hook from

the equipment under test, the Edge will send 850ms COD.

Far-end disconnect

timer expires.

Disconnect to start of new call

timer starts.

Note: If equipment under test goes back off-hook before the

Far-

End Disconnect

timer expires, the Edge goes back to looking for

step 3.

Disconnect to start of new call

timer expires.

Edge ready to receive next call.

If no Audio Message is programmed for the channel, proceed directly to step 3.

Far-End Disconnect

guard time

Call

Setup

Call Connected

Call Disconnect

TSP Sends

Ringing

Delay Before

Message

TSP Plays

Audio

Message

Disconnect
To Start Of

New Call

Содержание TSP Edge


















































































































































































Результаты поиска

Содержание TSP Edge

Отзывы:

Похожие инструкции для TSP Edge

Бренды по названию

Популярные бренды

Teltone TSP Edge, Руководство пользователя

Результаты поиска

Содержание TSP Edge

Отзывы:

Похожие инструкции для TSP Edge

Бренды по названию

Популярные бренды