manualshive.com logo in svg

Teledyne 6 RU Chassis, Руководство по эксплуатации

Поделиться
Скачать
Teledyne 6 RU Chassis Скачать руководство пользователя страница 33

6 RU SSPA Chassis Operations Manual 

202058 REV AA 

33 

2.3.1.14 IP Info Page 4 

 
This page contains information about the web password and Trap NMSIP. 
 

• 

WebPassword 

— Indicates the selected password for the web page in-

terface. A blank value indicates that the web interface does not require a 
password protected login. 

• 

TrapNMSIP 

— Shows the selected IP address for the SNMP trap recipi-

ent. (Version 6.00). 

 

2.3.1.15 Firmware Info Page 1 

 
This page is available through the Operation Setup menu, and provides information 
about the SSPA micro-controller unit firmware revision level and build date. 
 

2.3.1.16 Firmware Info Page 2 (version 4.0) 

 
This page provides additional SSPA information. 
 

• 

SSPA ID 

– SSPA unique serial and model number. 

• 

UserInfo 

– User information string, which could be set over SNMP proto-

col (see SNMP MIB info for details) 

 

2.3.1.17 Firmware Info Pages 3, 4, 5, 6 and 7 (version 4.0) 

 
These pages contain information about the firmware revision level and unique ID of 
each RF module. A unit may contain one to four RF modules and one pre-amp. Pages 
will remain blank if a particular module is not installed.  
 

2.3.1.18 Hardware Info Page 8 (version 6.00) 

 
This page shows the hardware ID markers for the power supply configuration, the type 
of hardware build of the DigitalCore board and the I/O board. This information is for 
factory use only.  
 

2.3.1.19 HPA Local Time Page 9 (version 6.00) 

 
This page shows the optional device clock. The device clock is a user selectable pa-
rameter. User set time is power dependent. A backup capacitor is used to keep the 
clock running while the SSPA is powered down. The clock will need to be reset if the 
unit remains without power longer than 5 hours.  
 
Clock output format is Year/Month/Day Hours:Minutes:Seconds. Only 24-Hour format 
is supported at this time. 
 

Содержание 6 RU Chassis













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды