manualshive.com logo in svg

Teledyne 6 RU Chassis, Руководство по эксплуатации

Поделиться
Скачать
Teledyne 6 RU Chassis Скачать руководство пользователя страница 2

2 

202058 REV AA 

6 RU SSPA Chassis Operations Manual 

Teledyne Paradise Datacom,  a Teledyne Telecommunications company, is a single source for high 
power solid state amplifiers (SSPAs), Low Noise Amplifiers (LNAs), Block Up Converters (BUCs), and 
Modem products. Operating out of two primary locations, Witham, United Kingdom, and State College, 
PA, USA, Paradise Datacom has a 20 year history of providing innovative solutions to enable satellite 
uplinks, battlefield communications, and cellular backhaul. 
 

Teledyne Paradise Datacom  

Teledyne Paradise Datacom 

328 Innovation Blvd., Suite 100 

2&3 The Matchyns, London Road, Rivenhall End 

State College, PA 16803 USA 

Witham, Essex CM8 3HA United Kingdom 

(814) 238-3450 (switchboard) 

+44 (0) 1376 515636 

(814) 238-3829 (fax) 

+44 (0) 1376 533764 (fax) 

 
Information in this document is subject to change without notice. The latest revision of this document 
may be downloaded from the company web site: http://www.paradisedata.com. 
 

Use and Disclosure of Data 

 
The information contained herein is classified as EAR99 under the U.S. Export Administration  
Regulations. Export, re-export or diversion contrary to U.S. law is prohibited. 
 
No part of this document may be reproduced or transmitted in any form without the written permission of  
Teledyne Paradise Datacom LLC. 
 
All rights are reserved in this document, which is property of Teledyne Paradise Datacom LLC. This  
document contains proprietary information and is supplied on the express condition that it may not be 
disclosed, reproduced or transmitted in any form without the written permission of Teledyne Paradise 
Datacom LLC. 
 
All other company names and product names in this document are property of the respective  
companies. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

© 2014-2015 Teledyne Paradise Datacom 

Printed in the USA 

Содержание 6 RU Chassis













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды