Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 242

background image

Maintenance, Service, and Repair

Transmission
Page 10

9. Pre set the carrier

bearing preload by
tightening the housing
carrier bearing race ring
nut until it requires 1.5
to 3.3 ft-lbs to rotate the
differential assembly.

NOTE: Rotate the carrier

assembly whenever
adjusting the ring nuts.

10. Mark the position of

each carrier bearing
ring nut in relation to the
drive housing and
cover and then remove
the differential
assembly, do not allow
the ring nuts to rotate.

If the ring and pinion gears or bearings are

replaced then the pinion gear must be re-

shimmed. Improper pinion gear shims will

result in drive noise and premature failure.

Refer to Pinion Gear Shimming

Instructions.

11. Install the pinion gear.

Re-shim if required.

12. Install the pinion gear

holding tool (96-500-
42) and tighten the
pinion nut enough to
keep the pinion gear
from rotating.

13. Install the differential

assembly.

14. Install the cover and all of the cover bolts. Torque

to 45-50 ft-lbs.

15. Check the gear lash between the ring and pinion

gears. The gear lash should be .005 to .007 inches.

16. Adjust the gear lash if needed by tightening or

loosening the carrier bearing race ring nuts. The
two ring nuts must be turned equally in opposite
directions.

NOTE: To move the ring gear closer to the pinion:

Loosen the housing carrier bearing race ring
nuts and tighten the cover carrier bearing race
ring nut equally.

NOTE: To move the ring gear away from the

pinion:
Loosen the cover carrier bearing race ring
nut and tighten the housing carrier race
ring nut equally.

17. Install the locking roll pins into the housing and

cover to lock the ring nuts in place.

18. Remove the pinion gear holding tool.

19. Install the primary reduction gear case, axles and

housings, motor, and install the complete drive
onto the vehicle.

20. Fill the drive with oil. Refer to the

Lube Chart

section for information regarding type of oil. Refer
to

Change Oil

section for information regarding

the proper oil level..

21. Lower the vehicle.

22. Reconnect the main positive and negative cables

at the batteries.

23. Remove the blocks from behind the wheels.

24. Test drive the vehicle.

The two ring nuts must be turned the same

amount in opposite directions. This allows

the carrier assembly to be positioned with

the proper gear lash without upsetting the

bearing preload. If the ring nuts are not

turned the same amount, then the bearing

preload will no longer be correct and will

result in drive noise and premature failure.

«
...
84
85
86
87
88
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренд: U-Line Страницы: 4

Бренд: Paccar Страницы: 40

Turbo-Max 6100 Series

Бренд: SAC Страницы: 82

Бренд: U-Line Страницы: 6

Бренд: Gregory Страницы: 49

BUSINESS CLASS M2 100

Бренд: freightliner Страницы: 198

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды