Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 115

Страница: 115 / 242

Maintenance, Service, and Repair

Batteries

Page 9

Returning to Service

6. Thoroughly clean the batteries and battery

compartment. Refer to

Cleaning

in this section

for information regarding cleaning the batteries.

7. Check the electrolyte level and charge the

batteries. Refer to

Watering

in this section for

information regarding checking the electrolyte
level.

8. Test the batteries. Refer to

Testing

section for

information on testing the batteries.

9. The batteries are now ready to be put back into

service.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Set the park brake.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренды по названию

Популярные бренды

Taylor-Dunn B0-T48-48 Taylor Truck T48, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренды по названию

Популярные бренды