Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 47

Страница: 47 / 242

Maintenance, Service, and Repair

Steering

Page 3

If the clamps are positioned so that they

contact other components, it may result in

steering failure and loss of control of the

vehicle causing property damage and/or

severe bodily injury.

12. Adjust the drag link so that it can be easily inserted

into the pitman arm.

13. Tighten the ball joint or rod end nut as specified

below:

Ball joint - 40-45 ft-lbs.
Rod end - 20-25 ft-lbs.

14. If equipped with ball joints, position the ball joint

clamps in their original location and orientation.

15. Tighten the ball joint clamps (28-32 ft. lbs.) or the

rod end jam nuts on the drag link.

16. Untie the steering wheel and the front wheels.

17. Reconnect the main positive and negative cables

at the batteries.

18. Rotate the steering wheel from a full left turn to a

full right turn and make sure that the ball joint
clamps do not contact any other component.

19. Remove the blocks from behind the wheels.

20. Release the parking brake and test drive the

vehicle.

Rotate the steering wheel from a full left

turn to a full right turn and make sure that

the ball joint clamps do not contact any

other component. Clamps positioned so

that they contact other components may

result in steering failure and loss of control

of the vehicle causing severe bodily injury

and/or property damage.

A Y

L OR - DUN

Go About

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Taylor-Dunn B0-T48-48 Taylor Truck T48, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 47 / 242

Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы: