Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 62

Страница: 62 / 242

Maintenance, Service, and Repair

Brakes
Page 4

ADJUST THE PARKING BRAKE

Wheel Park Brake

The parking brake is actuated through a pin in the center of the rear left and right brake body on the rear
axles.

6. Release the park brake.

7. Loosen the jam nuts on the park brake linkage

that is connected to the brake arm on the caliper
assembly.

8. Tighten the brake linkage until it is difficult to rotate

the brake arm clevis pin and then loosen the
linkage 1-turn.

9. Tighten the jam nuts on the park brake linkage.

10. Repeat this procedure for both rear wheels.

11. Set the park brake.

12. Reconnect the main positive and negative cables

at the batteries.

13. Remove blocks from behind the wheels.

14. Release the park brake and test drive the vehicle.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Taylor-Dunn B0-T48-48 Taylor Truck T48, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 62 / 242

Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы: