Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 242

Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 60

Maintenance, Service, and Repair

Brakes
Page 2

Disc Brake Rotor

NOTE: The front brake rotor is an integral part of the

front hub. If the brake rotor is worn beyond
its service limits, then the front hub must be
replaced. Refer to

Front Axle Service

for

information on replacing the front hub.

NOTE: Depending on the rear axle configuration, the

rear brake rotor may be an integral part of
the rear axle. If the brake rotor is worn beyond
its service limits, then the rear axle must be
replaced. Refer to

Transmission

section

for information regarding replacing the rear
axle

NOTE: The wheel must be removed to accurately

measure the rotor thickness. Refer to

Tires

and Wheels

section for information on

removing the wheel.

1. Measure the run out of the rotor at its maximum

diameter. If the run out exceeds 0.005, then the
rotor must be machined. Do not machine the rotor
beyond its service limits.

NOTE: A bent axle or damaged rear axle could cause

excessive brake rotor run out.

2. Measure the thickness of the brake rotor in 3

places. If the brake rotor thickness is less than
0.20-inches, then the rotor must be replaced.

Disc Brake Pads

NOTE: The brake pad must be removed to accurately

measure the
lining thickness.
Refer to

Replace

the Front or
Rear Brake
Pads

section for

information on
removing the
brake pads.

Measure the brake pad
lining at the thinnest point
on the pad. If the brake
pad lining is 1/16-inch or
less then the brake pad
must be replaced.

It is recommended to
replace the left and right
side brake pads as a set.

Current Taylor-Dunn

®

brakes are asbestos

free. However, there is the possibility that

the original brakes were replaced with

aftermarket parts containing asbestos.

Since this possibility exists, all brake parts

should be handled as if they contain

asbestos. Refer to Appendix C for

recommended handling precautions.

Do not use a rotor that is worn beyond its

service limits. A rotor worn beyond its

service limits could fail and cause loss of

brakes resulting in severe bodily injury

and/or property damage.

INSPECT THE SERVICE BRAKE

«
...
58
59
60
61
62
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов