Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 242

Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 9

INTRODUCTION

Page-3

HOW TO USE THIS MANUAL

This manual is organized into five main sections:

INTRODUCTION

This section describes how to use this service manual
and how to identify your vehicle.

Safety Rules and Operating Instructions

This section outlines the safety and operational issues,
location and operation of controls, and the operational
checks that are to be performed on this vehicle. It
also includes various subjects that should be included
in the operator and service training program.

Maintenance Service and Repair

This section gives specific information on the servicing
of the vehicle and a schedule for maintenance checks.

Electrical and Charger Troubleshooting

This section identifies the troubleshooting procedures
for testing the electrical system and battery charger.

Illustrated Parts

This section provides an illustrated view of various
assemblies. The illustrations are accompanied by
tables identifying the parts.

Conventions

Symbols and/or words that are used to define
warnings, cautions, instructions, or notes found
throughout this manual. Refer to the examples below.

Note: Alerts the reader to additional

information about a subject.

Model B 2-48 equipped
with the Dump Bed option

Model R 3-80 shown equiped with a cargo
box and steel cab with doors options

A shaded box with and the word “Warning”
and the symbol

above denotes a

warning. This warning alerts the reader of

a high voltage hazard that may result in

injury to themselves or others. Be sure to

follow any instructions contained within a

warning and exercise extreme care while

performing the task.

A shaded box with the word “Warning” and
the symbol

above denotes a warning. A

warning alerts the reader of a hazard that

may result in injury to themselves or

others. Be sure to follow any instructions

contained within a warning and exercise

extreme care while performing the task.

A box with the word “CAUTION” and the
symbol

above denotes a caution and is

used to inform the reader that property

damage may occur. Be sure to exercise

special care and follow any instructions

contained with in a caution.

«
...
7
8
9
10
11
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов