Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 242

Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 79

Maintenance, Service, and Repair

Transmission

Page 3

MOTOR REMOVAL AND
INSTALLATION

NOTE: Some applications will require removing the

drive assembly from the vehicle to remove
the motor. Refer to

Removing and

Installing the Drive Assembly

for

information on removing the drive assembly.

Some vehicles are equipped with an automatic electric
brake. The automatic electric brake is sandwiched
between the drive motor and the gear case. The electric
brake is retained by the drive motor mounting screws.
Once the motor is removed the electric brake will no
longer be retained by any hardware.

6. Remove the wires from the motor.

NOTE: Label the motor wires with the number of the

motor terminal before they are removed from
the motor.

7. If equipped,

remove the
motor support
bracket u-bolt
(only used on
larger motors).

8. Remove the

motor mounting
bolts and slide
the motor off of
the input shaft.

9. Install the motor in reverse order.

NOTE: Apply a light coating of grease part number

94-421-34 to the splines on the transmission
input shaft only.

10. Reconnect the main positive and negative cables

at the batteries.

11. Remove the blocks from behind the wheels.

12. Release the park brake and test drive the vehicle.

Support bracket u-bolt

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Set the park brake.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Set the park brake.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

REAR HUB OR ROTOR

NOTE: The torque specification for the axle hub bolt

is 275 ft-lbs. An impact wrench will be
required to remove the bolt.

NOTE: The axle hub bolt has a special thread locking

compound applied to the threads. If this bolt
is removed, it must be replaced.

6. Raise the wheel off of the ground.

7. Remove the tire/wheel assembly, Refer to

Tires

and Wheels

section for information regarding

removing the tire/wheel assembly.

8. Remove the axle hub bolt and washer and remove

the hub from the axle.

9. Remove the outer brake pad. Refer to section

Brake Service

for information regarding

removing the brake pads.

10. Remove the rotor.

«
...
77
78
79
80
81
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов