Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 57

Страница: 57 / 242

Maintenance, Service, and Repair

Steering

Page 13

Reassembly

1. Lightly lubricate all parts before reassembly.

2. Install a new worm shaft seal and pitman shaft

seal into the housing.

3. Install the upper worm bearing cup.

4. Divide the ball bearing into two equal groups.

5. Position the ball nut onto the worm as shaft as

shown in the illustration.

6. Insert the ball guides into the ball nut.

7. Insert each group of bearings into the ball guides.

NOTE: Do not rotate the worm shaft while installing

the bearings. This may cause one or more
of the bearings to enter the crossover
passage in the ball nut, causing improper
operation.

8. Install the ball guide clamp.

9. Place the upper worm bearing on the worm shaft

and install the worm shaft/ball nut assembly into
the housing being careful not to damage the worm
shaft seal.

10. Install the assembled worm bearing adjuster into

the housing and tighten just enough to remove all
play in the worm shaft.

11. Install, but do not tighten the worm bearing adjuster

lock nut.

12. Rotate the worm shaft to center the ball nut in the

housing.

13. Place a new gasket onto the housing and install

the assembled pitman shaft/side cover onto the
housing using two of the three mounting bolts.

14. Pack the steering gear with grease through the

open side cover bolt hole and then install the bolt.

15. Adjust the steering gear.

NOTE: Refer to

Adjust the Steering

gear section

for information regarding adjusting the
steering gear.

16. Once the adjustments are completed, make sure

that the locking ring and jam nut are tight.

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренды по названию

Популярные бренды

Taylor-Dunn B0-T48-48 Taylor Truck T48, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренды по названию

Популярные бренды