Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 242

Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 17

SAFETY RULES AND OPERATING INSTRUCTIONS

Safety Rules

Page 5

DASH (STARTING S/N 180000)

1) Headlight Switch

The headlight switch is located on the left sideof the
instrument panel. Push the top of the switch to turn the
lights on. Push the bottom of the switch to turn the lights
off.

2) WIper Switch (Optional)

Other electrical accessories are controlled from the
auxiliary switch or switches. The actual function of the
switch may vary depending on the electrical option
installed.

3) Strobe Switch (Optional)

Other electrical accessories are controlled from the
auxiliary switch or switches. The actual function of the
switch may vary depending on the electrical option
installed.

6) Smart View gauge

See Smart View Display later in this section

7) Horn Switch

Depress the switch to sound the horn, release it to turn it
off.

8) Key-Switch

A key-switch, located on the lower center of the instrument
panel, turns on the vehicle. Rotate the key clockwise to
turn the vehicle power on, counterclockwise to turn the
vehicle power off.

The key-switch should be in the “OFF” position whenever
the operator leaves the vehicle.

This switch is also designed to secure and disable the
vehicle. The key can only be removed when the key-
switch is in the “OFF” position.

4) Forward-Off-Reverse Switch

The forward-off-reverse switch, located on the right side
of the instrument panel, determines the direction of travel
of the vehicle. Push the top of the switch to engage the
forward direction. Push the bottom of the switch to
engage the reverse direction.

DO NOT SWITCH from forward to reverse or vice-versa
while the vehicle is in motion. Make sure the vehicle is
completely stopped before shifting.

The forward-off-reverse switch should be in the center
“OFF” position, with the key-switch off and the park brake
set whenever the operator leaves the vehicle.

5) Hi-Low Switch (optional)

The high-low switch will be switch #5 or #7 depending on
what other electrical options are installed (see above).
Toggle the switch lever up for normal speed. Toggle the
switch lever down for slow speed.

«
...
15
16
17
18
19
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов