Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя | Manualshive

Страница: 144 / 242

background image

Battery Charger

Page 6

MN-402-000

Lock Out Relay

Before continuing, Refer to Testing the Interlock Relay
procedure in this section. This is an external test to confirm if
the relay is functioning properly.

This test should only be performed if it has been
determined that the relay is not closing by the procedure
indicated above

.

1. Remove the charger

form the vehicle.

2. Remove the charger

cover.

3. Disconnect the

black and white
relay coil wires from
the relay.

4. Measure the resistance across the relay coil terminals.

• 120 v charger: 2,700 Ohms (nominal)
• 220 v charger: 11k Ohms (nominal)
If out of specification then the relay is faulty.

4. Reconnect the wires to the relay.

5. Disconnect the Violet/Black wires from the relay.

6. Connect an Ohm meter across the relay terminals.

7. Connect the charger AC wires to a power outlet. The relay

should “click” and the meter should indicate a closed circuit.

• If the relay does not “click” then check the wiring to

the relay coil.

• If the meter does not indicate a closed circuit, then

the relay is faulty.

• If the relay tests OK, check continuity of the Violet/

Black wires.

8. Disconnect then charger from the AC power source and

remove all test leads.

While connected to an AC outlet, the charger cabinet

must remain electrically grounded. Disconnect both

of the battery leads and unplug the charger from

the AC source before disconnecting any electrical

component or wire. Failure to do so may result in

serious bodily injury.

Transformer

1. Remove the charger form the vehicle.

2. Remove the charger cover.

3. Connect an AC volt meter to the transformer secondary

winding accessed at the Cathode on each SCR (blue and
violet wires). Set the meter to read up to 150 volts RMS.

4. Connect the charger AC wires to a power outlet.

5. Depress the Low Voltage Start switch and record the

voltage indicated on the meter.

6. Disconnect the charger from the AC power source and

remove all test leads.

7. The transformer secondary RMS AC voltage should be

approximately 2.1 times the rated DC voltage of the
charger.

Note:

Typically, the secondary voltage of a failed
transformer will be significantly below
specification.

Make sure that the meter leads do not touch any

other component or wire. Other components will

be damaged if the leads touch any other component

or wire.

High Voltage inside the charger. Do not touch any

internal components while the charger is plugged

in. Touching internal components may result in

electric shock causing severe boldily injury or death.

High Voltage inside the charger. Do not touch any

internal components while the charger is plugged

in. Touching internal components may result in
electric shock causing severe boldily injury or death.

«
...
142
143
144
145
146
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренд: Kenworth Страницы: 110

Бренд: Capacity Страницы: 116

Бренд: BigJoe Страницы: 28

Бренд: mecalac Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды