Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 242

background image

Maintenance, Service, and Repair

Brakes

Page 11

1. Make sure the key-switch is in the “OFF” position, then remove

the key.

2. Place the forward-reverse switch in the center “OFF” position.
3. Set the park brake.
4. Place blocks under the front wheels to prevent vehicle movement.
5. Disconnect the main positive and negative cables at the batteries.

The pistons are very fragile. If the piston is damaged it must be

replaced. Failure to replace a damaged piston could lead to brake

failure and result in property damage and/or severe bodily injury.

REPAIR THE BRAKE BODY

Hydraulic brake system components must be kept clean. Make sure

your work area is free from dirt and debris and will contain any brake

fluid spills. Any debris or contaminates left in the brake system could

lead to brake failure and result in property damage and/or severe

bodily injury.

Do not ingest brake fluid or allow contact with skin or eyes. Always

wear protective clothing and a face shield when working with or

around brake fluid.
SKIN CONTACT
Flush area immediately with water for several minutes. If a rash or

skin irritation develops, get medical attention immediately.
EYE CONTACT
Immediately flush the eye with water for 15 minutes and call

physician.
INGESTION
Get medical attention immediately.

6. Remove the brake body from the vehicle.

NOTE: Refer to

Replace the Brake Body Assembly (front or rear)

section for information on

removing the brake body.

7. Pull the pistons out of the brake body.

8. Remove the piston rubber boot.

9. Remove the piston o-ring from inside of the brake body.

10. Inspect and replace parts as required.

11. Lubricate the brake parts with clean DOT 5 brake fluid from a sealed container.

On systems to be filled with DOT 3 brake fluid, DOT 5 fluid is used for

lubriacation only . See Brake Fluid Specification on page 1 of this section.

«
...
67
68
69
70
71
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренд: Jacobsen Страницы: 20

Бренд: UD Trucks Страницы: 244

Бренд: Komatsu Страницы: 739

Бренд: RAM Commercial Страницы: 16

Бренд: Toolex Страницы: 8

Freightliner Cascadia 2021

Бренд: Daimler Страницы: 322

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды