Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 242

background image

Maintenance, Service, and Repair

Steering

Page 9

REPLACE THE BALL JOINTS, TIE RODS, AND DRAG LINK

This section will refer to two different types of ball joints. One
type is has a grease fitting and a tapered shaft where it is installed
on the steering arm or pitman arm. The second cannot be greased
and has a straight shaft. See the illustrations to the right.
Depending on the configuration of your vehicle, it may be
equipped one or both types of ball joints.

In this text:
The first type will be referred to as a “Ball Joint.”
The second type will be referred to as a “Rod End.”

NOTE: If a rod end or ball joint is worn out, we recommend

replacing all of the ball joints and/or rod ends as a set.

Rod End

Ball Joint

Rod End Nut

Rod End

Jam Nut

Steering
Sleeve

Steering Arm

Replacing a Rod End

6. Raise the front of the vehicle and support with

jack stands.

7. Loosen the rod end jam nut or clamp on the

steering sleeve.

8. Remove the rod end nut.

9. Remove the rod end from the steering arm.

HINT: Count the number of turns required to remove

the rod end from the steering sleeve. This
will make it easier to realign the wheels.

10. Install the new rod end into the steering sleeve.

Screw it into the sleeve the same number of turns
counted in the previous step. Do not tighten the
rod end clamp or jam nut at this time.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

11. Install the rod end into the steering arm. Tighten

the rod end nut to 20-25 ft-lbs.

12. Realign the front wheels.

NOTE: Refer to the

Steering

section for information

regarding realignment of the front wheels.

13. Lower the vehicle.

14. Reconnect the main positive and negative cables

at the batteries.

15. Remove the blocks from behind the wheels.

16. Release the park brake and test drive the vehicle.

«
...
51
52
53
54
55
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренд: Vestil Страницы: 21

Бренд: Surtek Страницы: 12

Бренд: U-Line Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды