Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 99

Страница: 99 / 242

Motor Service

Motor

Page 5

REPLACING THE BRUSHES

NOTE: It is recommended that all four brushes be

replaced as a set.

NOTE: Motors without removable brush covers must

be disassembled to replace the brushes.
Refer to

Motor Inspection-Disassembly

section for information on taking the motor
apart.

NOTE: Some motors are equipped with brush pairs.

These motors must be disassembled to
replace the brushes. Refer to

Motor

Inspection-Disassembly

section for

information on taking the motor apart. Refer
to the

Motor Parts List

for your vehicles

brush configuration.

NOTE: Some motors have brush leads that are routed

through or behind the brush holder assembly.
In this case, the brush holder assembly must
be removed to replace the brushes.

NOTE: The motor must be removed from the vehicle

for this procedure. Refer to

Transmission

Service

section for information on removing

the motor.

Motors with brush covers and brushes with
termination screws

1. Remove the brush covers.

2. Loosen the brush wire retaining screw and remove

the brush from the brush holder. Be careful with
the brush spring and do not let it slip off of the
spring mount. If the spring comes off, then the
motor must be disassembled. Refer to

Motor

Inspection-Disassembly

section for

information on taking the motor apart.

3. Install the new brushes in reverse order.

4. Be certain that the brush springs do not rest up

against the brush wires. Refer to illustrations in

Motor Inspection-Assembly

for proper brush

spring position.

Motors with brush pairs or not equipped
with brush covers

1. Disassemble the motor. Refer to

Motor

Inspection-Disassembly

section for information

on taking the motor apart.

2. Remove the brush holder.

Note: Remember the position and routing of the brush

crossover leads. They must be reinstalled in
the same position.

3. Remove the brush termination screws or the

armature studs and remove the brushes from the
brush holder.

4. Install the new brushes in reverse order.

5. Reassemble the motor. Refer to

Motor

Inspection-Assembly

for information regarding

reassembling the motor.

Brush Spring Orientation

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренды по названию

Популярные бренды

Taylor-Dunn B0-T48-48 Taylor Truck T48, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренды по названию

Популярные бренды