Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 242

Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 129

Sevcon Troubleshooting

Page 13

Electrical Troubleshooting

Test 7. FORWARD AND REVERSE SWITCH FAULT

Turn the key switch ON, place the forward and reverse switch in the center OFF position and
perform the following tests:

TEST 7.1:

Referencing battery positive, test the voltage on the center
terminal of the F&R switch (Black wire).

If the voltage equals battery volts, then skip ahead to
test #7.2.
If the voltage does not equal battery volts, then check
the wire from the F&R switch to the battery voltage circuit
breaker.

Stop trouble shooting here and repair the problem. When
the repair is completed, completely retest the vehicle before
lowering the drive wheels to the ground.

TEST 7.2:

If the vehicle does not travel in reverse, skip ahead to
test #7.3.
Place the forward and reverse switch in the FORWARD
position.

Referencing battery positive, test the voltage at the Blue/Black
wire on the F&R switch.

If the voltage equals battery volts, skip ahead to test
#7.4.
If the voltage does not equal battery volts, then the F&R
switch has failed.

Stop trouble shooting here and repair the problem. When
the repair is completed, completely retest the vehicle before
lowering the drive wheels to the ground.

After any repairs are made, completely retest

the vehicle before lowering the drive wheels to

the ground. Failure to retest the vehicle could

result in unexpected movement of the vehicle

resulting in injury or property damage.

This troubleshooting guide is written in

sequential order. All tests must be performed in

the order that they are written. Starting in the

middle or skipping sections when not instructed

to do so may lead to invalid test results.

«
...
127
128
129
130
131
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов