Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 242

background image

Maintenance, Service, and Repair

Tires and Wheels
Page 2

TIRE INFLATION

There are many tire options available with varying tire
pressures. Refer to the side wall of your tire for
information regarding the tire pressure for your tires.

The illustration to the right is an example of the side wall
information on a tire.

Tire pressures must be checked when the tire is cold.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Set the park brake.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

TIRE INSPECTION

6. Check the tire pressure. Refer to

Tire Inflation

section for information on checking the tire
pressure.

7. Inspect the tire tread depth. Minimum

recommended tread depth is 1/16-inch. There are
a series of tread depth wear indicators around
the circumference of the tire. They will appear as
1/2-inch bands across the tread as the tire
approaches its wear limit (see illustration below).
Replace the tire if any tread depth indicator can
be seen or any part of the tread depth is 1/16-
inch or less. Refer to

Replace the Tire

section

for information regarding replacing the tire.

8. Inspect for uneven tire wear on the front tires.

Uneven tire wear could be a result of an
improperly inflated tire or a misaligned or
damaged front end.

NOTE: Refer to

Tire Inflation

section or

Steering

Component Service

section for information

on proper tire inflation or front end wheel
alignment.

9. Inspect the inner and outer side walls for cracks.

If any cracks are seen, then the tire should be
replaced. Refer to

Replace the Tire

section for

information regarding replacing the tire.

10. Inspect the valve stem for cracks. If any cracks

are seen, then the valve stem should be replaced.
It is also recommended that the valve stem be
replaced whenever the tire is replaced.

NOTE: Refer to

Replace the Tire

section for

information regarding replacing the valve
stem.

11. Inspect the tread and side walls for debris in the

rubber that could lead to a puncture. If any debris
is found it should be removed and the tire
inspected for a leak.

«
...
102
103
104
105
106
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренд: RAM Страницы: 332

Бренд: Kalmar Страницы: 317

Бренд: RAM Commercial Страницы: 284

Бренд: Taylor-Dunn Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды