Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 242

background image

Battery Charger

Page 14

MN-402-000

LESTRONIC II CHARGER

SLA batteries must be charged with a charger

configured for SLA batteries. Use of any other

charger will result in damage to the batteries and

premature failure of the batteries.

Built-In

Portable

Test Equipment Required for
Troubleshooting

• Digital Multi Meter (DMM) with diode and capacitor test

function, FLUKE 79® model shown in the troubleshooting
illustrations.

• Clamp on DC ammeter to measure up to 40-Amps.

Important Notes and Instructions

• This troubleshooting guide assumes a familiarity with the

use of a digital multimeter including, voltage tests,
continuity tests, and diode testing. If you are not familiar
with any part of these tests, refer testing to a qualified
technician.

• Make sure that the AC electrical outlet is in good working

condition.

• Make sure that the AC voltage at the electrical outlet is the

same as the AC voltage on the charger nameplate.

• Make sure the batteries are in good condition and no less

than 80% discharged as per hydrometer reading.

• The battery voltage must be above approximately 65% of

the chargers rated DC voltage. If the batteries are below
approximately 65% of the chargers rated DC voltage, the
charger will not turn on.

• If the charger exhibits intermittent problems, it must be in

the failed mode for troubleshooting.

• Battery volts = Full voltage available at the batteries at the

time of the test being performed.

• This test procedure must be performed in the order it was

written. If starting in the middle or skipping sections when
not instructed to do so, the proper results will not occur. If
the test result is good, then proceed to the next test or go
to the next section if instructed to do so.

«
...
150
151
152
153
154
...
»

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B0-T48-48 Taylor Truck T48

Magliner H-1382

Бренд: U-Line Страницы: 6

1949-50-51 F-Series Truck

Бренд: Ford Страницы: 30

Бренд: U-Line Страницы: 9

Бренд: U-Line Страницы: 15

Automizer Versa Hand

Бренд: Labrie Страницы: 80

Бренд: RAM Страницы: 340

Бренд: WorkSmart Страницы: 9

Бренд: Verhagen Leiden Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды