Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя

Страница: 143 / 242

Battery Charger

Page 5

MN-402-000

TROUBLESHOOTING

SCR Assembly

Test:

Perform the test setup before starting this procedure.

1. The test light should be OFF. If the light is ON then one of

the SCR’s is shorted. Skip ahead to Gate Test.

2. Momentarily touch the resistor to one of the gate terminals.

3. The test light should turn ON and stay ON when the resistor

is removed. The voltmeter should read 0.88 volts (nominal).
If the light does not turn ON then the SCR has failed. Skip
ahead to Gate Test.

4. Disconnect then reconnect the battery and repeat the test

on the other SCR.

Gate Test:

This test should only be performed if it has been determined
that one of the SCR’s have failed.

Perform the following on BOTH SCR’s.

1. Disconnect the 12 volt battery and all test leads.

2. Measure the resistance from the SCR Anode terminal (+)

to the Gate terminal (-).

3. The resistance should be high, around 15 meg Ohms.

4. If the reading is low, then the gate is shorted. If the gate

has shorted on either SCR, then it is likely that the control
board has been damaged and must also be replaced.

Note:

Both SCR’s must be replaced as a set.

Note:

This test passes current through the transformer
and fuse. Confirm both the transformer and fuse
are good before continuing.

Tools required for this test:

12 volt battery, Test light, Volt meter, 300 Ohm resistor.

Test Setup:

1. Remove the charger form the vehicle.

2. Remove the charger cover.

3. Disconnect the Gate wires from both SCR’s.

Note: The other wires are soldered and cannot be removed.

4. Disconnect the control board J1 connector.

5. Connect the 12 volt battery positive to the charger DC

output Black wire.

Connect one lead of the resistor to the 12 volt battery
positive. The resistor should be on a wire long enough to
reach the SCR’s.’

6. Connect the 12 volt battery negative to one of the test light

leads.

7. Connect the other test light lead to the charger DC output

Red wire.

8. Connect a voltmeter to the charger Black and Red output

wires.

Содержание B0-T48-48 Taylor Truck T48



















































































































































































































































Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренды по названию

Популярные бренды

Taylor-Dunn B0-T48-48 Taylor Truck T48, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Похожие инструкции для B0-T48-48 Taylor Truck T48

Бренды по названию

Популярные бренды