Tadano TT-800XXL1 Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 267

background image

2

W587-0011E

K-1.

K-1.

Crane Cab Glass

[NOTICE]

Wipe away any excessive adhesive.

11. Fit the molding on the circumference of the new

glass and bond its end joint with an instant
aneous adhesive.

Glass

Molding

IW587-0010E04

[NOTICE]

Apply the adhesive so that its cross sectional form

is as shown in the figure by shaping it with a
spatula.

For a portion where there is a clearance between

the glass and rubber dam, apply the adhesive to a
bead height of more than 5 mm (0.2 in).

◆

Install the glass in less than 30 minutes after
application of the adhesive.

12. After installing the trim on the glass bonding

portion frame of the cab body, apply the adhesive
to the glass bonding surfaces.
• Adhesive:

S-511A [Black paste to use when room
temperature is higher than 15°C (59°F)]
S-511F-1 [Black paste to use when room
temperature is lower than 15°C (59°F)]
Cemedine Co., Ltd.

IW587-0010E05

8 10

Rubber dam backing paper

Adhesive beads

Rubber dam

Trim

Unit : mm (1mm = 0.039 in)

13. Remove the rubber dam backing paper.

(Refer to the figure.)

[NOTICE]

◆

When the glass installed, press it only once. Do not
press it repeatedly (This can form air bubbles).

Excess adhesive must be wiped away with a

spatula and white gasoline.

14. Set and press the new glass against the cab

while aligning the marks (masking tape pieces put
in Step 3) on the glass with those on the cab
body.

IW587-0010E06

Rubber dam

Molding

Glass

Trim

2. Bonding the joint between windshield

glass and roof glass

1. Bond 50 mm (1.95 in) wide pieces of masking

tape to places 1 to 2 mm (0.039 to 0.078 in) away
from the edges of windshield glass and roof glass.

2. Remove the rubber dam backing paper.

3. Install and press the new glass while aligning the

marks with those on the cab body.

4. Secure the windshield glass and roof glass on the

cab body with an adhesive tape.

5. Fill the space between the windshield glass and

roof glass with the adhesive (cemedine’s S-511A
or S-511F-1) and reshape it with a spatula so that
it will be flush with the glass.

[NOTICE]

After the glass has been bonded, allow a curing

period of more than two hours. Don’t move the
glass.

After the glass has been bonded, secure the glass

on the cab body with a rubber tape or elastic cord,
or by other suitable means.

6. Remove the masking tapes and wipe away

excessive adhesive using white gasoline or
acetone.

IW587-0010E07

Roof glass

Masking tape

Front glass

Adhesive

Trim

50

1　

2

～

Rubber dam

Unit : mm (1mm = 0.039 in)

«
...
153
154
155
156
157
...
»

Содержание TT-800XXL1












































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TT-800XXL1

Бренд: B&K Страницы: 12

Бренд: Modulate Страницы: 2

Бренд: A&D Страницы: 2

Бренд: A&D Страницы: 176

Бренд: Badger Meter Страницы: 16

Бренд: Rangevision Страницы: 28

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренд: Dantel Страницы: 6

Бренд: Zero 88 Страницы: 22

Бренд: Yaasa Страницы: 20

Бренд: YASKAWA Страницы: 1166

ABS-Lock III-BE

Бренд: ABS Страницы: 8

Бренд: RAB Страницы: 4

TRACER pH PockeTester 1741

Бренд: LaMotte Страницы: 16

Бренд: Psiber Страницы: 16

Бренд: König Electronic Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды