Tadano TT-800XXL1 Скачать руководство пользователя страница 187

Страница: 187 / 267

K-2

Air Conditioner

W701-0160E

11.3 Car air conditioner system diagnosis table III (Electrical system)

Operation trouble

phenomenon of

functional parts

First operation

check and

confirmation

Second operation check

and confirmation

Diagnosis result

(phenomenon of

principal cause)

Possible cause

Measures (specific part

name and repair method)

--------------------------------

No fuse blowing
(normal).

--------------------------------

Measures from diagnosis

of 2) and 4).

1) Neither
compressor clutch
nor blower motor
operate.

Check of fuse
blowing.

--------------------------------

Fuse blowing.

Short-circuit of compressor clutch
or blower motor system wiring.

Repair

Clutch does not suck.

----------------------------

Clutch failure.

Replace

Clutch does suck.

Either of thermo amp., pressure
SW, or thermistor is failure.

Check and replace parts.

Clutch does not suck.

Check voltage of

clutch relay connector.

0 (zero) V

Either of clutch relay signal

circuit or vehicle side electronic
control amplifier is failure.

Check parts, and repair or
replace parts.

2) Only
compressor clutch
does not suck.
(Others are
operating.)

Connect battery
directly to clutch
terminal.

Clutch does suck.

Short-circuit both ends

of thermo amp. bypass
connector, pressure SW,
and thermistor.

Clutch does not suck.

Check voltage of

clutch relay connector.

Approx. 12V

Either of clutch relay or clutch

power circuit (disconnection) is
failure.

Check parts, and repair or
replace parts.

Clutch does not suck.

----------------------------

Thermistor failure.

Replace

Clutch does not suck.

Thermo amp. failure.

Replace

3) Compressor
clutch suction does
not stop.

Remove thermistor
from thermo amp.

Clutch does suck.

Remove thermo amp.

power supply connector.

Clutch does suck.

Clutch relay contact failure.

Replace

Blower motor does not
work.

----------------------------

Blower motor failure.

Replace

Blower motor works.

Blower switch failure.

Replace

Blower system cords
disconnection.

Repair

4) Only blower
motor does not
work.

Connect battery
directly to "+"
terminal of blower
motor.

Blower motor works.

Connect L.M.H of blower

switch directly to battery
terminal.

Blower motor does not
work.

Rresistor failure.

Replace

Fan motor does not work.

----------------------------

Fan motor failure.

Replace

0 (zero) V

Signal circuit is open, and thermo
amp. failure.

Check parts, and repair or
replace parts.

5) Condenser fan
motor does not
work.

Connect battery
directly to "+"
terminal of fan
motor.

Fan motor works.

Check voltage of

condenser fan relay
connector.

Approx. 12V

Condenser fan relay contact
failure or fan motor power circuit
open.

Check parts, and repair or
replace parts.

6) Compressor
clutch slips.

Check air gap.

--------------------------------

-----------------------------

Air gap is large.

Adjust air gap.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды