Tadano TT-800XXL1 Скачать руководство пользователя страница 189

Страница: 189 / 267

K-2

Air Conditioner

W701-0160E

11.4 Car air conditioner system diagnosis table IV (Electronic thermo system)

Operation

trouble

phenomenon of

functional parts

Guessing of

trouble functional

parts

Check and confirmation of

operational parts

Diagnosis result

(Refer to temperature

characteristic for thermistor.)

Possible cause

Measures

(Thermistor amplifier

replacement, and connector

repair.)

Resistance is small.
(Abnormal if resistance is
about 7k

or less.)

Thermistor failure.

Replace thermistor.

Check thermistor.

Measure resistance of
thermistor connector.

Resistance is about 2k

(25

℃

Thermistor is normal.

----------------------------

Check thermo
volume.

Turn OFF thermo volume.

Compressor clutch is turned
OFF.

Thermo volume is
short-circuited.

Replace thermo volume.

Compressor
clutch stayed
ON.

Check relay
contact and
thermo amp.

Remove connector of
thermistor.

Compressor clutch cannot be
turned OFF. (Stayed ON)

Relay contact joining.
Thermo amp. failure.

Replace relay or thermo amp.

Check thermistor.

Measure resistance of
thermistor connector.

Resistance is about 7k

more.

Thermistor failure.

Replace thermistor.

Check thermo
volume.

Measure resistance of thermo
volume terminal.

Resistance is

∞

(infinity).

Thermo volume is
disconnected.

Replace thermo volume.

Compressor
clutch stayed
OFF.

Check relay
contact and
thermo amp.

Detach connector of thermistor,
and short-circuit thermo amp.
side connector.

Compressor clutch cannot be
turned ON.

Relay contact joining.
Thermo amp. failure.

Replace relay or thermo amp.

Tester indicator changes if
applying shock to thermo
volume.

Contact failure in thermo
switch.

Replace thermo switch.

Check thermo
switch.

Check conduction in thermo
volume terminal.

Tester indicator does not
change even if applying
shock to thermo volume.

Thermo switch is normal.

----------------------------

Check thermo
amp.

Remove thermistor, and
short-circuit thermo amp. side
connector.

When applying shock to
thermo amp., compressor
clutch does chattering.

Soldering failure (or,
caulking failure) in thermo
amp.

Replace thermo amp.

Compressor
clutch does
chattering.

Check contact
condition in wiring
connector.

Twist connectors.

Compressor clutch does
chattering.

Connector failure.

Repair connector.

Insufficient
cooling. (Clutch
works ON and
OFF.)

Replaces
thermistor with
new one.

Gets cold normally.

Thermistor failure.

Deterioration of thermistor.

Replace thermistor.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды