Tadano TT-800XXL1 Скачать руководство пользователя страница 142

Страница: 142 / 267

W305-023

H-2

Boom Length and Angle Detector

2. Disassembly and reassembly

Removing the cord

. Remove the connector and the cord lock from the

end of the cord. Wind up the cord on the drum
slowly until no tension of the spiral spring is
applied on the cord.

2. Loosen the clamp and remove the cover (2 place).

3. Disconnect the cable, potentiometer and angle

detector from the terminal, and remove the cover
and the cable together.

4. Loosen the set screw and remove the gear. Then

remove the screw and detach the speed reducer.

[NOTICE]

Remove the speed reducer straight upward. Do not

twist it while removing.

5. Remove the retaining ring and bolt, and separate

the case from the drum assembly.

[NOTICE]

Put match marks on the case and the plate to

identify the direction for removing the sub-cord.

IW305-0230E03

Retaining ring

Plate

Match marks

Sub-cord

Case

Bolt

6. Remove the nut and separate the drum assy from

the plate.

IW305-0230E04

Drum assy

Plate

Nut

7. Remove the slip ring assy from the drum assy.

Then remove the solder that bonds the slip ring
and the cord.

IW305-0230E05

Cord

Slip ring assy

Core wire

Shield wire

8. Detach the whole old cord from the drum assy.

2.2 Installing the cord

. Wind a yellow tape around the new cord as a

0-marker.

Drum end

0-marker (yellow tape)

IW305-0230E06

0.5m

Red tape

(

ft)

43m

(

.6ft)

9.33m

(30.6ft)

2. Pass the new cord through the hole of the drum

assy. Solder it on the slip ring assy.

[NOTICE]

Attach the cord core wire to the inner slip ring.

Attach the shield wire to the outer slip ring.

Completely insulate the soldered section.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды