Tadano TT-800XXL1 Скачать руководство пользователя страница 237

Страница: 237 / 267

Y-4

Check (Crane Operation)

WY04-05

Check (Crane Operation)

. Hoisting

[Condition]

• Load

:None

• Engine speed

:650-

300 min

[Procedure]

. Shift the boom telescoping lever to full stroke first.

2. Make sure that the main winch moves slowly

while the auxilialy winch lever is slightly operated.

3. Make sure that the main winch does not move

while the auxilialy winch lever is operated to full
stroke.

2. Jib

. Make sure that anti-two block function does not

work during the jib set status is registered.

2. Check the jib lock indicator lamp.

• Make sure that the lamp is lit when the jib slides

out of the center support on the boom.

JIB LOCK

Lamp is lit

IWY04-05

0E0

• After the jib is stowed, make sure that the lamp

is not lit.

3. Detection of contact of the front jack

with ground

. Set the crane no outriggers before extending the

front jack.
Stop front jack operation jus before the front jack
touches the ground.

2. Then slightly retract the front jack indicative

symbol on the AML is not hightlight in this
situation.

3. Extended the front jack again.

Continue extending operation for more than 4

seconds after the jack float touches the ground.
Make sure that the front jack indicative symbol on
the AML is hightlighted in this situation.

4. Setup the outrigger emergency

. Turn ON the switch of the panel on upper right in

the cab.

2. Confirm the indicator is lighting.

OFF

Indicator

IWY04-05

0E02

3. Confirm the extending width can be set manually

with AML regardless of the extending width.
(same to all outriggers)

5. Upper outrigger operation (option):

It becomes possible when
connecting PTO and becoming
the crane work possible.

. Confirm an individual operation performs correctly,

and in addition, confirm the following.

• All operation extending: Only four outriggers

operate.

• All operation retracting: Four outriggers and

front jack operate.

2. O/R switch non-neutral position lamp must light if

either Ext./Ret. selection swich or Jack/Slide
selection switch is actuated.

IWY04-05

0E03

Lamp is lit

3. After the status of O/R is registered with AML,

confirm the status of AML bocomes on-tire if
retracting O/R or F/J.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды