Tadano TT-800XXL1 Скачать руководство пользователя страница 230

Страница: 230 / 267

WY05-0740E

Y-2

Air Bleeding Procedure

4. Winch circuit (main and aux.)

[NOTICE]

Bleed the main and auxiliary winch circuits by

following the procedures below. The procedures are
common to the both circuits.

Winch motor

Bleed the winch motor by following either (

) or (2).

(

) Pour the hydraulic oil through the drain port into

the casing until the oil flows out.

(2) Perform the slow hoist-up or hoist-down

operation for approx.

minute.

4.2 Winch counterbalance valve

Repeat the slow hoist-up and slow hoist-down
operations, while increasing the engine speed
gradually to the maximum (2

50 min

) until no more

air bubbles come out of the air bleeder screw.

4.3 Winch brake release circuit

Repeat the slow hoist-up and slow hoist-down
operations with the engine idling until no more air
bubbles come out of the air bleeder screw.

5. Jib lock pin and jib offset cylinder

[NOTICE]

Bleed the jib lock pin, jib offset cylinder by following

either (

), (2), or (3).

(

) Start the engine, turn the PTO switch on, and

raise the engine speed to approx. 2,

50 rpm.

(2) Attach a hose to the bleeder screw (A).and

loosen the bleeder screw. In this condition, repeat
the rapid jibset operation to the retract or the
extend until no more air bubbles come out of the
air bleeder screw.

Air bleeder plug

IWY05-0580E02

Air bleeder plug

(A)

(B)

(C)

(D)

Jib lock pin

Jib offset cylinder

[NOTICE]

Bleed in the order of bleeder screws, (A), (B), (C)

and (D).

(3) After air-bleeding is over, fasten the bleeder

screw and remove the hose.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды