Tadano TT-800XXL1 Скачать руководство пользователя страница 186

Страница: 186 / 267

K-2

Air Conditioner

W701-0160E

Trouble

phenomena

other than A/C

system

Disorder section

Phenomenon explanation to

consider other factors

Diagnosis result

(phenomenon of principal

cause)

Possible cause

Measures (specific part name

and repair method)

Sound is generated when
compressor starts.

--------------------------------

Vibration or slip by belt
looseness (continuous sound
'Quuuu!'). Screw looseness
failure.

Tension belt, replace, or
re-tighten screw.

Sound is generated from
radiator fan and condenser
fan.

--------------------------------

Motor-fan shaft shaking, bearing
breakdown, fan damage, or
fan/shroud come in contact.

Repair or replace.

Noise sounds.

Engine room side

Sound is generated from
parts installation section
(shaking when touching).

--------------------------------

Dropout of fixed bolt, looseness,

or damage of brackets.

Tighten appropriately, or
replace brackets.

Blocking in condenser fin.

--------------------------------

Wash condenser fin.

Revolution of condenser fan
is slow.

Condenser fan failure.

Replace condenser fan motor.

Vehicle
overheats
easily.

Condenser unit

Condenser is set in front of
radiator.

High-pressure is high. (High
pressure is high at idling.)

Same cause as refrigeration
circuit system-I. (Hot air flows in
condenser.)

Same measures as
refrigeration circuit system-I

Blocking in radiator fin.

Wash or replace radiator fin.

--------------------------------

Dirt inside radiator.
Radiator filler cap failure.
Water pump failure.
Blocking in water thermo.

Check and replace.

Radiator coolant is
shortage.

--------------------------------

Check leakage and replenish,

or replace radiator.

Fan belt and water pump
belt are slippage.

--------------------------------

Adjust belt tension or replace
belts.

Vehicle
overheats
easily.

Vehicle side

Trouble around radiator.

Revolution of radiator
cooling fan is slow, or
slippage.

Radiator fan failure.

Replace

Engine
(revolutions) is
overrun.

Vehicle side

Engine revolution adjusting
device

--------------------------------

Raising idling speed too much or
overheat.

Adjust idling speed to a
regulated value, and adjust
engine. Take measures for
overheat.

Smells
unpleasant.

Cooling unit

--------------------------------

Smoke of Tabaco, dust, and

mold, etc. are adhered or
deposited to the evaporator fin.

Wash evaporator.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды