Tadano TT-800XXL1 Скачать руководство пользователя страница 144

Страница: 144 / 267

W305-023

H-2

Boom Length and Angle Detector

3. Draw out the cord slightly from the drum and

make sure that the resistance between the red
and white terminals increases smoothly.

4. Connect the cable to the terminals for the

potentiometer and angle detector.

5. Attach the cover.

6. Pull the cable to eliminate slack, and tighten the

clamp. (2 places)

7. Install the cord lock on the cord end and install

the lead wires and the connector close to the cord
end. Completely insulate the soldered
connections.

IW305-0230E

Cord

Yellow

8.5 m

0.08 m

Cord lock

Connector

0.25 m

0-marker

White Lead wire

Wind HI-BOND tape for
waterproofing and then
wind insulating tape.

(27.9ft)

(0.8ft

)

(0.26ft)

8. Check for conduction and shortcircuit between

the terminals of the sub-cord connector and the
cord connector.

IW305-0230E

Cord

Sub-cord

2.3 Replacing spiral spring

[NOTICE]

If the spiral spring is broken, replace the whole

drum assy. For removing and installing the spring,
refer to the "Removing the cord" and "Installing the
cord" above mentioned.

2.4 Disassembling the potentiometer

(for boom length detector)

[NOTICE]

If both the cord and spiral spring are faulty, remove

the detector assy from the boom.

If only the potentiometer is faulty, it is not necessary

to remove the detector.

. Loosen the 2 clamps and remove the bolt and

cover.

2. Disconnect the lead wire terminals (3 pieces) and

cable terminal from the potentiometer, and
remove the potentiometer together with the
bracket.

[NOTICE]

Before replacement, disconnect the wiring to the

boom angle detector from the pin terminal section to
disconnect the lead wires (red and black) from the
boom angle detector.

IW305-0230E

Bracket

Pin terminal

To boom angle detector

Potentiometer

Red

Spring

Gear

Lead wire

Black

3. Remove the gear and the spring, and detach the

potentiometer from the bracket.

4. Remove the connector and the cord lock from the

end of the cord. Wind up the cord on the drum
slowly until no tension of the spring is applied on
the cord.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды