Tadano TT-800XXL1 Скачать руководство пользователя страница 182

Страница: 182 / 267

K-2

Air Conditioner

W701-0160E

11 Diagnosis table

11.1 Car air conditioner system diagnosis table I (Refrigeration circuit)

A/C system

trouble

phenomenon

Status explanation

of A/C system

pressure

Phenomenon explanation to

consider other factors

Diagnosis result (phenomenon of

principal cause)

Possible cause

Measures (specific

part name and
repair method)

Bubble does not appear easily to
sight glass when dripping water on
condenser.

Sight glass is transparent with liquid
refrigerant.

Liquid level in sight glass does not
fall even if about two seconds have
passed since A/C OFF.

Refrigerant overcharge

Discharge
refrigerant up to
proper amount.

When idling, pressure at high
pressure side is high.

There is a spot where hot air
enters in front of condenser.

Hot air of condenser outlet
air and radiator outlet air
flows in front of condenser.

Install packing or
rubber sheet to a
part where hot air
hits.

----------------------------- --------------------------------

Much air contaminates in
refrigeration circuit.

Deflate from circuit
and fill refrigerant.
Replace receiver
drier (R/D).

Dirt or blocking in condenser fin.

------------------------------

Wash condenser.

Insufficient
cooling.

Pressure at high
pressure side is
high

Ventilation to condenser is bad.

Air volume of condenser fan is few. Condenser fan failure.

Replace
condenser fan.

No cooling

High pressure is
high, and low
pressure is low.

Pressure at high pressure side rises
immediately after A/C ON. Bubbles
appear in sight glass. (High
pressure side is uncertain for
vehicle with charge valve following
R/D.)

--------------------------------

Blocking in high-pressure
circuit between COMP. and
R/D.

Remove blocked
foreign object, or
replace part.

Bubbles appear in sight glass.

Oil blots to the piping and parts.
Gas detector detects.

Gas leakage from piping
joint and parts.

Check joint
looseness and
re-tighten, or
replace part.

Insufficient
cooling.

Both pressures at
high pressure side
and low pressure
side are low.

Bubbles appear in sight glass, then
it changes transparently.

------------------------------

TXV adjustment failure
(reduced too much), or gas
leakage in therms sensor
tube.

TXV readjustment
or replace.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды