Tadano TT-800XXL1 Скачать руководство пользователя страница 192

Страница: 192 / 267

K-2

Air Conditioner

W701-0160E

12.2 Compressor diagnosis chart (1/2)

Cool

g f

ail

Compressor does not work.

Clutch terminal voltage is normal. 12V or 24V

Clutch terminal voltage low.

Clutch terminal voltage none.

Both

r and blo

otor

Bubble does not disappear even if charging gas.
Cloudiness does not disappear for new refrigerant.

Oil or gas leakage from parts other than compressor
or piping joint. Check with gas detector.

Gas or oil leakage from compressor.
(No leakage found other than from compressor.)
Check with gas detector.

Both high and low pressure are low.

High-press. is slightly low, and low-press. is high.

Gas has not been charged for more than
one season.

Gas will be discharged within 1-2 months.
Check with gas detector.

High-pressure is high.

Will not get cold when continuously driving at high speed.

Air volume of blower motor is few.

App

ear

anc

dir

Clutch seizure.

Amateur and rotor clearance failure. (airgap failure)

Core disconnection or short-circuit.

Shaft does not rotate. (internal lock)

Compressor cylinder does not become hot.
Cloudiness does not

Cloudiness does not disappear for new refrigerant.

Cloudin
ess

Mechanical seal, gasket, and charge valve.

Leakage from oil plugs.

Leakage from front housing or cylinder block joint.

Repair

Leak from hose etc. naturally.

Repair

Charge gas.

Repair

one season.
(No abnormality.)

Check oil.

Adjust oil amount.

Repair

Valve damage or scroll damage.
(Refer to Note 3 on next page.)

Gasket blowout. (Refer to Note 3 on next page.)

Too much oil.

Clutch bearing failure because of belt overstretch.

Shaft does not rotate.

There is caught even if shaft rotates.

Eas

y to

ver

heat

Compressor does not work.

Phenomena other than compressor.

Refer to "Car air conditioner system diagnosis table II".

Phenomenon and diagnosis result

Cause

Remedy

(Refer to Note 1 and 2 on next page.)

Gas is not decreased after two years
or more.

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды