Tadano TT-800XXL1 Скачать руководство пользователя страница 190

Страница: 190 / 267

K-2

Air Conditioner

W701-0160E

Operation

trouble

phenomenon of

functional parts

Guessing of

trouble functional

parts

Check and confirmation of

operational parts

Diagnosis result

(Refer to temperature

characteristic for thermistor.)

Possible cause

Measures

(Thermistor amplifier

replacement, and connector

repair.)

Replaces
thermistor with
new one.

Insufficient cooling status does
not change.

--------------------------------

Thermo amp. internal
failure.

Replace thermo amp.

Positioned correctly.

--------------------------------

Thermistor failure.

Replace thermistor.

Insufficient
cooling. (Clutch
works ON and
OFF.)

Check installation
condition of
thermistor.

Incorrect position or comes off.

--------------------------------

Install thermistor in correct
position.

Insufficient
cooling. (Clutch
stayed ON)

Refer to other
diagnosis tables.
(Excluding the
cause of
electronic thermo
system.)

-------------------------------- --------------------------------

--------------------------------

Содержание TT-800XXL1












































































































































































































































































Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды

Tadano TT-800XXL1, Руководство по обслуживанию

Результаты поиска

Содержание TT-800XXL1

Отзывы:

Похожие инструкции для TT-800XXL1

Бренды по названию

Популярные бренды