Tadano TT-800XXL1 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 267

background image

K-2

K-2

Air Conditioner

7

W701-0160E

3.3 Refrigerant

1. The substance that circulates through the

refrigeration cycle, and functions to transmit heat,
is known as the refrigerant. In our air conditioning
system, HFC134a is used. It is a freon-based
refrigerant, but does not contain chlorine.

2. As shown in the figure below, the refrigerant

HFC134a remains in liquid form at relatively high
temperatures when it is strongly compressed.
However, at low pressures it vaporizes at
temperatures as low as 0°C (32°F) or
-10°C (14°F).

3. This means, for example, that if the refrigerant

vaporizes at 0°C (32°F), then the evaporator is
also at 0°C (32°F). The air that passes through
this evaporator should be cooled.

4. If the pressure is reduced so that the refrigerant

evaporates at -5°C (23°F), the evaporator is also
maintained at -5°C (23°F). This results in the
formation of frost, which inhibits the flow of air
through the evaporator and prevents cooling.

5. The vaporized refrigerant must then be liquefied.

However, it is impossible to obtain a temperature
as low as 40°C (104°F) in a hot summer
environment.

6. If 60

°

C (140°F) is possible, HFC134a will become

a liquid at 60°C (140°F) if the pressure is
approximately 1.7 MPa (246.5 psi) or above.
When the gaseous refrigerant is compressed to
1.7 MPa (246.5 psi) (by the compressor), the gas
temperature rises to approximately 80°C (176°F).

7. Therefore, the temperature of the gas as it enters

the condenser is 80°C (176°F). The curve above
shows that when the refrigerant gas is cooled by
20°C (68°F), it becomes a liquid at approximately
60°C (140°F) by the time it reaches the condenser
outlet.

«
...
158
159
160
161
162
...
»

Содержание TT-800XXL1












































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TT-800XXL1

Бренд: Jacobs Ladder Страницы: 16

Бренд: lancer Страницы: 12

Бренд: UNIA Страницы: 62

Бренд: BACtrack Страницы: 16

Бренд: Rangevision Страницы: 28

Бренд: jcb Страницы: 41

Бренд: Zero 88 Страницы: 12

Бренд: Zeiss Страницы: 119

Бренд: Zehnder Rittling Страницы: 32

Бренд: MAGSTIM Страницы: 86

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренд: Össur Страницы: 65

Бренд: Össur Страницы: 92

Бренд: Össur Страницы: 38

Бренд: B medical systems Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды